Horiba electrode stand for LAQUA 1500 & 2000 series

Stress-free measurement - professional model Water quality analysis is repeatedly performed in laboratories on a daily basis. Our high-end benchtop model was developed to provide simplicity with excellent on-site usability - from operation and maintenance through to troubleshooting.Ideal for student training and routine applications. Good value for money: no bells and whistles that sounds good but is rarely used. From a renowned manufacturer whose company started with pH meters as early as 1945.Highly accurate measurements  Accepts up to 5 conductivity calibration points Automatic calibration at 84μS/cm, 1413μS/cm, 12.88mS/cm, & 111.8mS/cm standards Displays average calibration factor Selectable cell constant Allows 1-point salinity calibration and temperature calibration Pre-programmed TDS and salinity curves for various applicationsScope of delivery: Measuring instrumentUniversal mains adapter with 6 plugs Operating instructions Starter set version additionally contains: 9382-10D plastic body conductivity electrode, cell constant k=1.0 84 µS/cm, 1413 µS/cm, 12.88 mS/cm conductivity standard (1 x 250ml each) with electrode holder

High-end laboratory measuring instrument for analytics  Dear customers, herewith we offer you our highly professional Horiba laboratory table-top measuring instrument of the 2000 series.  The LAQUA 2000 series laboratory tabletop meter has a very high-quality 5 inch display with backlighting which shows you all the important information, such as the measured value with up to three decimal places (depending on the resolution), the temperature, the date with time and much more.  The LAQUA 2000 series also offers you an adequate device memory with automatic data storage after a set time interval to document your daily measurements accurately over a long period of time. To protect the device settings from unauthorised access, they are password-protected. After your measurements, you can easily transfer all measurement data from the device to your PC via a USB cable in CSV, Excel and Pdf formats using the DAS20 software.  In order to facilitate your daily work with the device, the table measuring device visualises the correct calibration, the stable measurement as well as the electrode wear condition. The operation is intuitive because the available keys are marked with symbols and abbreviations. After the analysis, you can clean the device easily and in a time-saving manner with a damp cloth, as the surface is dirt-repellent due to its nature. The electrode stand included in the starter set can be used to hold two electrodes and adjust their height. This allows you to individually align your electrode to your container or glass for calibration and measurement. Special features of the Laqua EC2000 model (multi-parameter): The EC2000 is a measuring instrument which evaluates the conductivity in various measuring ranges and also measures the TDS, resistance, salinity and temperature values. Conductivity-resistivity-TDS-salinity wide measuring range from 0.001μS/cm to 2,000 S/cm  allows automatic and manual conductivity calibrations  records individual and average calibration factors after conductivity calibration  Calculates resistance, TDS and salinity based on measured conductivity  7 conductivity ranges:   0.000 to 1.999 μS/cm (k = 0.1)  2.00 to 19.99 μS/cm (k = 0.1, 1)  20.0 to 199.9 μS/cm (k = 0.1, 1, 10)  200 to 1999 μS/cm (k = 0.1, 1, 10)  2.00 to 19.99 mS/cm (k = 0.1, 1, 10)  20.0 to 199.9 mS/cm (k = 1, 10)  0.200 to 2.000 S/cm (k = 10) Below we would like to show you in full the general functions of the Horiba LAQUA 2000 series: internal memory for up to 2000 data sets, measurement data with time and date information records and stores data in the unit memory based on a specified time interval a 4-digit password protects the meter set-up mode from unauthorised access data can be transferred to a computer and exported in the following formats CSV/Excel/PDF GLP/GMP  compliance of the instrument as data can be displayed, recorded and printed with date and time stamp on the instrument Software updates can be downloaded to the instrument Calibration reminder function, indicates that it is time to calibrate (alarm adjustable up to 90 days) Electrode holder is mounted on the meter and can hold up to 2 electrodes (rotates 360º and can be moved up and down 30cm). Electrode holder only included in the starter set.Displays measurement stability in measurement and calibration mode displays electrode condition based on calibration data smooth surface, easy cleaning RS-232/USB, therefore easy PC and printer connection and free instrument software Ergonomic design for easy viewing and operation Clearly labelled and easy-to-use ports for communication and measurement 5" digital display with backlight, shows all important measurement values and status Automatic calibration, recognises a wide range of standard solutionsadjustable switch-off time (up to 30 minutes) temperature compensation, the temperature in °C or °F is either automatically detected if a temperature sensor is connected (ATC mode) or manually entered by the user several measuring modes: Auto-Stable mode signals a stable measured value,Auto-Hold mode holds a stable measured valueReal Time mode continuously displays current readings small meter footprint of 155 x 150 mm, saves valuable space Temperature detection, easy display of sample temperature user selectable resolution, up to 3 digits Fixed and individual calibration pointsEasy navigation, navigate through the settings menu by up, down, right and left Scope of delivery: Measuring instrumentUniversal mains adapter with 6 plugs Operating instructions Starter set version additionally contains 9382-10D conductivity electrode with plastic body, cell constant k=1.0 84 µS/cm, 1413 µS/cm, 12.88 mS/cm (1 x 250ml each)with electrode holder Flow cell available in combination with 9371-10 stainless steel conductivity cell for ultrapure water measurement (300-2C-C) Manufacturer part number:Meter only   EC2000 (3200896965) Starter-set   EC2000-S (1300098881)

Stress-free measurement - professional model Water quality analysis is repeatedly performed in laboratories on a daily basis. Our multiparameter laboratory measuring instrument was developed to provide simplicity with excellent on-site usability - from operation and maintenance through to troubleshooting. Simultaneous measurement is possible by connecting two electrodes at the same time.Ideal for student training and routine applications. Good value for money: no bells and whistles that sounds good but is rarely used. From a renowned manufacturer whose company started with pH meters as early as 1945.Highly accurate measurements Automatic temperature compensation Accepts up to 6 pH- and up to 5 conductivity- calibration points Auto calibrates USA, NIST, & DIN pH buffers Displays offset & average slope Allows 1-point ORP-, salinity- and temperature- calibrationScope of delivery: Measuring instrumentUniversal mains adapter with 6 plugs Operating instructions Starter set version additionally contains: 9625-10D refillable pH electrode with plastic body 9382-10D plastic body conductivity electrode, cell constant k=1.0 pH 4, 7 and 10 buffer solutions & 3.33M KCl (1 x 250ml each)84 µS/cm, 1413 µS/cm, 12.88 mS/cm conductivity standard (1 x 250ml each)with electrode holder

High-end laboratory measuring instrument for analytics  Dear customers, herewith we offer you our highly professional Horiba laboratory table-top measuring instrument of the 2000 series.  The LAQUA 2000 series laboratory tabletop meter has a very high-quality 5 inch display with backlighting which shows you all the important information, such as the measured value with up to three decimal places (depending on the resolution), the temperature, the date with time and much more.  The LAQUA 2000 series also offers you an adequate device memory with automatic data storage after a set time interval to document your daily measurements accurately over a long period of time. To protect the device settings from unauthorised access, they are password-protected. After your measurements, you can easily transfer all measurement data from the device to your PC via a USB cable in CSV, Excel and Pdf formats using the DAS20 software.  In order to facilitate your daily work with the device, the table measuring device visualises the correct calibration, the stable measurement as well as the electrode wear condition. The operation is intuitive because the available keys are marked with symbols and abbreviations. After the analysis, you can clean the device easily and in a time-saving manner with a damp cloth, as the surface is dirt-repellent due to its nature. The electrode stand included in the starter set can be used to hold two electrodes and adjust their height. This allows you to individually align your electrode to your container or glass for calibration and measurement. Special features of the Laqua PC2000 model (multi-parameter): The PC2000 is a combination of the ION2000 and the EC2000 with the advantage that you can measure all parameters with one device. Dual input, connection of 2 electrodes at the same time. pH-ORP wide measuring range; -2.000 to 20.000 pH  high accuracy; ± 0.003 pH  resolution: 0.1, 0.01 or 0.001 pH  continuous display of calibrated points  display of offset and slope - by segment and average up to 5 pH  calibration points ± 2000.0 mV  1-point redox calibration  automatically recognises and calibrates USA, NIST, NIST2 and DIN pH buffers  allows CUST (Custom) buffers for manual calibration  Conductivity-resistivity-TDS-salinity wide measuring range from 0.001μS/cm to 2,000 S/cm  allows automatic and manual conductivity calibrations  records individual and average calibration factors after conductivity calibration  Calculates resistance, TDS and salinity based on measured conductivity  7 conductivity ranges:   0.000 to 1.999 μS/cm (k = 0.1)  2.00 to 19.99 μS/cm (k = 0.1, 1)  20.0 to 199.9 μS/cm (k = 0.1, 1, 10)  200 to 1999 μS/cm (k = 0.1, 1, 10)  2.00 to 19.99 mS/cm (k = 0.1, 1, 10)  20.0 to 199.9 mS/cm (k = 1, 10)  0.200 to 2.000 S/cm (k = 10) Ions (ammonia, calcium, chloride, fluoride, nitrate, potassium)  Measurement ion-selective accepts combined and half-cell ion-selective electrodes wide measuring range from 0.000 μg/L to 9999 g/L accepts up to 5 user-defined ion calibration points choice of preferred units: μg/L - mg/L - g/L, ppm - ppt, mmol/L - mol/L Resolution of 4 significant digits after the decimal point with automatic scaling  Below we would like to show you in full the general functions of the Horiba LAQUA 2000 series: internal memory for up to 2000 data sets, measurement data with time and date information records and stores data in the unit memory based on a specified time interval a 4-digit password protects the meter set-up mode from unauthorised access data can be transferred to a computer and exported in the following formats CSV/Excel/PDF GLP/GMP  compliance of the instrument as data can be displayed, recorded and printed with date and time stamp on the instrument Software updates can be downloaded to the instrument Calibration reminder function, indicates that it is time to calibrate (alarm adjustable up to 90 days) Electrode holder is mounted on the meter and can hold up to 2 electrodes (rotates 360º and can be moved up and down 30cm). Electrode holder only included in the starter set.Displays measurement stability in measurement and calibration mode displays electrode condition based on calibration data smooth surface, easy cleaning RS-232/USB, therefore easy PC and printer connection and free instrument software Ergonomic design for easy viewing and operation Clearly labelled and easy-to-use ports for communication and measurement 5" digital display with backlight, shows all important measurement values and status Automatic calibration, recognises a wide range of standard solutionsadjustable switch-off time (up to 30 minutes) temperature compensation, the temperature in °C or °F is either automatically detected if a temperature sensor is connected (ATC mode) or manually entered by the user several measuring modes: Auto-Stable mode signals a stable measured value,Auto-Hold mode holds a stable measured valueReal Time mode continuously displays current readings small meter footprint of 155 x 150 mm, saves valuable space Temperature detection, easy display of sample temperature user selectable resolution, up to 3 digits Fixed and individual calibration pointsEasy navigation, navigate through the settings menu by up, down, right and left Scope of delivery: Measuring instrumentUniversal mains adapter with 6 plugs Operating instructions Starter set version additionally contains 9625-10D refillable pH electrode with plastic body 9382-10D conductivity electrode with plastic body, cell constant k=1.0 pH 4, 7 and 10 buffer solutions & 3.33M KCl (1 x 250ml each) 84 µS/cm, 1413 µS/cm, 12.88 mS/cm (1 x 250ml each) with electrode holderFlow cell available in combination with 9371-10 stainless steel conductivity cell for ultrapure water measurement (300-2C-C) Manufacturer part number:Meter only   PC2000 (3200896964) Starter-set   PC2000-SR (1300098882)

Stress-free measurement - professional model Water quality analysis is repeatedly performed in laboratories on a daily basis. Our high-end benchtop model was developed to provide simplicity with excellent on-site usability - from operation and maintenance through to troubleshooting.Ideal for student training and routine applications. Good value for money: no bells and whistles that sounds good but is rarely used. From a renowned manufacturer whose company started with pH meters as early as 1945.Highly accurate pH and ORP measurements Automatic temperature compensation Accepts up to 6 pH calibration points Auto calibrates USA, NIST, & DIN pH buffers Displays offset & average slope Allows 1-point ORP calibration and temperature calibrationScope of delivery: Measuring instrumentUniversal mains adapter with 6 plugs Operating instructions Starter set version additionally contains: 9625-10D refillable pH electrode with plastic body pH 4, 7 and 10 buffer solutions & 3.33M KCl (1 x 250ml each)with electrode holder

High-end laboratory measuring instrument for analytics  Dear customers, herewith we offer you our highly professional Horiba laboratory table-top measuring instrument of the 2000 series.  The LAQUA 2000 series laboratory tabletop meter has a very high-quality 5 inch display with backlighting which shows you all the important information, such as the measured value with up to three decimal places (depending on the resolution), the temperature, the date with time and much more.  The LAQUA 2000 series also offers you an adequate device memory with automatic data storage after a set time interval to document your daily measurements accurately over a long period of time. To protect the device settings from unauthorised access, they are password-protected. After your measurements, you can easily transfer all measurement data from the device to your PC via a USB cable in CSV, Excel and Pdf formats using the DAS20 software.  In order to facilitate your daily work with the device, the table measuring device visualises the correct calibration, the stable measurement as well as the electrode wear condition. The operation is intuitive because the available keys are marked with symbols and abbreviations. After the analysis, you can clean the device easily and in a time-saving manner with a damp cloth, as the surface is dirt-repellent due to its nature. The electrode stand included in the starter set can be used to hold two electrodes and adjust their height. This allows you to individually align your electrode to your container or glass for calibration and measurement. Special features of the LAQUA PH2000 model: The PH2000 allows you to measure the pH- or ORP- valuepH-ORP wide measuring range; -2.000 to 20.000 pH  high accuracy; ± 0.003 pH  resolution: 0.1, 0.01 or 0.001 pH  continuous display of calibrated points  display of offset and slope - by segment and average up to 5 pH  calibration points ± 2000.0 mV  1-point redox calibration  automatically recognises and calibrates USA, NIST, NIST2 and DIN pH buffers  allows CUST (Custom) buffers for manual calibration  Below we would like to show you in full the general functions of the Horiba LAQUA 2000 series: internal memory for up to 2000 data sets, measurement data with time and date information records and stores data in the unit memory based on a specified time interval a 4-digit password protects the meter set-up mode from unauthorised access data can be transferred to a computer and exported in the following formats CSV/Excel/PDF GLP/GMP  compliance of the instrument as data can be displayed, recorded and printed with date and time stamp on the instrument Software updates can be downloaded to the instrument Calibration reminder function, indicates that it is time to calibrate (alarm adjustable up to 90 days) Electrode holder is mounted on the meter and can hold up to 2 electrodes (rotates 360º and can be moved up and down 30cm). Electrode holder only included in the starter set. Displays measurement stability in measurement and calibration mode displays electrode condition based on calibration data smooth surface, easy cleaning RS-232/USB, therefore easy PC and printer connection and free instrument software Ergonomic design for easy viewing and operation Clearly labelled and easy-to-use ports for communication and measurement 5" digital display with backlight, shows all important measurement values and status Automatic calibration, recognises a wide range of standard solutionsadjustable switch-off time (up to 30 minutes) temperature compensation, the temperature in °C or °F is either automatically detected if a temperature sensor is connected (ATC mode) or manually entered by the user several measuring modes: Auto-Stable mode signals a stable measured value,Auto-Hold mode holds a stable measured valueReal Time mode continuously displays current readings small meter footprint of 155 x 150 mm, saves valuable space Temperature detection, easy display of sample temperature user selectable resolution, up to 3 digits Fixed and individual calibration pointsEasy navigation, navigate through the settings menu by up, down, right and left Scope of delivery: Measuring instrumentUniversal mains adapter with 6 plugs Operating instructions Starter set version additionally contains 9625-10D refillable pH electrode with plastic body pH 4, 7 and 10 buffer solutions & 3.33M KCl (1 x 250ml each) with electrode holder Manufacturer part number:Meter only   PH2000 (3200896829) Starter-set   PH2000-SR (1300098880)